LCD(Liquid Crystal Display) En: 두 판 사이의 차이

아두위키 : Arduwiki
잔글편집 요약 없음
잔글편집 요약 없음
 
1번째 줄: 1번째 줄:
{{#seo:|title=Arduwiki : Arduino LCD Guide|title_mode=append|keywords=Arduino, Information Science, Maker Learning, Performance Assessment, Buzzer, Arduino Project, Capstone Project, Arduino Example Code|description=This introduces how to control a LCD with Arduino (basic information, circuit, example code). It can be used in Information Science and Maker classes.}}
{{#seo:|title=Arduwiki : Arduino LCD Guide|title_mode=append|keywords=Arduino, Information Science, Maker Learning, Performance Assessment, LCD, Arduino Project, Capstone Project, Arduino Example Code|description=This introduces how to control a LCD with Arduino (basic information, circuit, example code). It can be used in Information Science and Maker classes.}}


[[파일:1602LCDimg1.jpg|class=coders100]]
[[파일:1602LCDimg1.jpg|class=coders100]]

2024년 8월 9일 (금) 11:04 기준 최신판


The Arduino LCD module is used to display characters or numbers, with 16x2 or 20x4 sized LCD displays being commonly used. This document covers LCDs that support I2C communication. Using the I2C interface instead of a typical parallel interface reduces the number of pins required and simplifies wiring. It can be easily connected to an Arduino board to visually represent information in various projects.


Main Specifications

  • Display Size: Commonly used sizes are 16x2 and 20x4.
  • Power Supply Range: 5V (supplied directly from the Arduino board)
  • Interface: I2C (SDA, SCL)
  • Character Set: Supports ASCII character set
  • I2C Address: Default is 0x27 or 0x3F (varies by module)


Features

  • Character Display: Can display alphabets, numbers, and special characters. For shapes or graphics, the capability is very limited, and graphic LCDs or OLEDs are more suitable.
  • Backlight Control: The backlight can be turned on and off, and brightness can be adjusted.
  • Cursor Control: The cursor position can be moved or hidden using setCursor().
  • Scroll Function: Text can scroll left and right. There is a variable resistor on the back for adjusting the brightness of the text.


Usage Examples

Library

  • Wire (This is a basic library, so no installation is needed.)


연결

It is the same regardless of size (16x2, 20x4).

I2C LCD Module Pin Arduino Uno Pin
VCC 5V
GND GND
SDA A4
SCL A5


1. Checking the Module Address

1-1. Code

#include <Wire.h>
 
void setup()
{
  Wire.begin();
  Serial.begin(9600);
  Serial.println("\nI2C Scanner");
}
 
void loop()
{
  byte error, address;
  int nDevices;
  Serial.println("Scanning...");
  nDevices = 0;
  for(address = 1; address < 127; address++ ) 
  {
    Wire.beginTransmission(address);
    error = Wire.endTransmission();
    if (error == 0)
    {
      Serial.print("I2C device found at address 0x");
      if (address<16) 
        Serial.print("0");
      Serial.print(address,HEX);
      Serial.println("  !");
      nDevices++;
    }
    else if (error==4) 
    {
      Serial.print("Unknow error at address 0x");
      if (address<16) 
        Serial.print("0");
      Serial.println(address,HEX);
    }    
  }
  if (nDevices == 0)
    Serial.println("No I2C devices found\n");
  else
    Serial.println("done\n");
  delay(5000);          
}


1-2. Execution Result


2. Displaying Text on the LCD

2-2. Code

#include <Wire.h>
#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27, 16, 2);

void setup()
{  
  // Initialize the LCD before use
  lcd.init();

  // Turn on the LCD's backlight
  lcd.backlight();

  // Set the cursor position to (0,0) (top-left corner)
  lcd.setCursor(0, 0);

  // Write the text to be displayed
  lcd.print("Gongzipsa");

  // Set the cursor position to (0,1)
  lcd.setCursor(0, 1);

  // Output the val value
  int val = 1004;
  lcd.print(val);
}

void loop(){}


2-2. Execution Result

Reference Document

Arduino LCD Doc


Purchase Link

GONGZIPSA