Potentiometer JP - 편집 역사

2025년 3월 20일 (목) 10:49에 ArduWiki님의 편집

2025-03-20T10:49:31Z

← 이전 판		2025년 3월 20일 (목) 19:49 판
1번째 줄:		1번째 줄:
	[[File:가변저항b10k.jpg\|center\|class=coders100]]		{{#seo:\|title=アルドゥウィキ：アルドゥイーノ可変抵抗器（ポテンショメーター）ガイド\|title_mode=append\|keywords=アルドゥイーノ, 情報科学, メーカー学習, パフォーマンス評価, 可変抵抗器（ポテンショメーター）, アルドゥイーノプロジェクト, キャップストーンプロジェクト, アルドゥイーノサンプルコード\|description=アルドゥイーノで可変抵抗器（ポテンショメーター）を活用する方法（基本情報、回路、サンプルコード）を紹介します。情報科学とメーカー授業で活用できます。}}[[File:가변저항b10k.jpg\|center\|class=coders100]]

	この装置は抵抗を変えることができます。		この装置は抵抗を変えることができます。

2025년 3월 20일 (목) 05:42에 ArduWiki님의 편집

2025-03-20T05:42:48Z

← 이전 판		2025년 3월 20일 (목) 14:42 판
1번째 줄:		1번째 줄:
	[[File:가변저항b10k.jpg\|center\|class=coders100]]		[[File:가변저항b10k.jpg\|center\|class=coders100]]

			この装置は抵抗を変えることができます。
			音量や光の明るさを調整するのに使用できます。

	~~This device can vary its resistance.~~

	~~It can be used to adjust the volume or the brightness of a light.~~		== '''必要なハードウェア''' ==
			* 可変抵抗器（本文ではB10Kを使用）
	== '''~~Required Hardware~~''' ==

	* ~~Variable resistor (B10K used in this text)~~
	* Arduino UNO		* Arduino UNO
	* ~~UNO Cable~~		* UNOケーブル
	* ~~Breadboard~~		* ブレッドボード
	* M-~~M Cable (3 pieces)~~		* M-Mケーブル（3本）

	~~== '''Connection''' ==~~

	* ~~Power is applied to the left and right, with the output coming from the middle.~~		== '''接続''' ==
	* ~~Power is applied to either the left or right, with the opposite terminal connected to GND.~~		* 左右に電源を接続し、中央から出力が得られます。
	* ~~Connecting as described, turning to the right increases the value, but if connected oppositely (right to GND, left to 5V), turning to the left increases the value.~~		* 左右どちらかに電源を接続し、反対側の端子をGNDに接続します。
			* 説明通りに接続すると、右に回すと値が増加しますが、逆に接続すると（右をGND、左を5Vに）、左に回すと値が増加します。

	{\| class="wikitable"		{\| class="wikitable"
	\|+		\|+
	!~~Variable Resistor~~		!可変抵抗器
	!Arduino UNO		!Arduino UNO
	\|-		\|-
36번째 줄:		34번째 줄:
	[[File:가변저항 회로.png\|center\|class=coders100]]		[[File:가변저항 회로.png\|center\|class=coders100]]

	== '''~~Example Code~~''' ==		== '''サンプルコード''' ==
	<syntaxhighlight lang="c++">		<syntaxhighlight lang="c++">
	#define input A0		#define input A0
42번째 줄:		40번째 줄:
	void setup()		void setup()
	{		{
	// ~~Start serial communication~~		// シリアル通信を開始
	Serial.begin(9600);		Serial.begin(9600);
	Serial.println("start");		Serial.println("start");
50번째 줄:		48번째 줄:
	void loop()		void loop()
	{		{
	// ~~Display the value of the variable resistor on the serial monitor~~		// 可変抵抗器の値をシリアルモニターに表示
	Serial.println(analogRead(input));		Serial.println(analogRead(input));
	delay(1000);		delay(1000);

ArduWiki: 새 문서: class=coders100 This device can vary its resistance. It can be used to adjust the volume or the brightness of a light. == '''Required Hardware''' == * Variable resistor (B10K used in this text) * Arduino UNO * UNO Cable * Breadboard * M-M Cable (3 pieces) == '''Connection''' == * Power is applied to the left and right, with the output coming from the middle. * Power is applied to either the left or right, with the opposite terminal con...

2025-03-20T05:35:50Z

새 문서: center|class=coders100 This device can vary its resistance. It can be used to adjust the volume or the brightness of a light. == '''Required Hardware''' == * Variable resistor (B10K used in this text) * Arduino UNO * UNO Cable * Breadboard * M-M Cable (3 pieces) == '''Connection''' == * Power is applied to the left and right, with the output coming from the middle. * Power is applied to either the left or right, with the opposite terminal con...

새 문서

[[File:가변저항b10k.jpg|center|class=coders100]]

This device can vary its resistance.

It can be used to adjust the volume or the brightness of a light.

== '''Required Hardware''' ==

* Variable resistor (B10K used in this text)
* Arduino UNO
* UNO Cable
* Breadboard
* M-M Cable (3 pieces)

== '''Connection''' ==

* Power is applied to the left and right, with the output coming from the middle.
* Power is applied to either the left or right, with the opposite terminal connected to GND.
* Connecting as described, turning to the right increases the value, but if connected oppositely (right to GND, left to 5V), turning to the left increases the value.

{| class="wikitable"
|+
!Variable Resistor
!Arduino UNO
|-
|Left
|GND
|-
|Middle
|A0
|-
|Right
|5V
|}
[[File:가변저항 회로.png|center|class=coders100]]

== '''Example Code''' ==
<syntaxhighlight lang="c++">
#define input A0

void setup()
{
// Start serial communication
Serial.begin(9600);
Serial.println("start");
Serial.println("======================");
}

void loop()
{
// Display the value of the variable resistor on the serial monitor
Serial.println(analogRead(input));
delay(1000);
}

</syntaxhighlight>
[[File:가변저항 테스트.png|center|class=coders50]]