ArduWiki: Created page with "{{#seo:|title=아두위키 : 불꽃 감지 모듈|keywords=아두이노,불꽃감지모듈,아두이노 불꽃감지모듈, 아두이노 센서 예제, 불꽃감지모듈 예제|description=아두이노에서 불꽃감지모듈을 사용하는 방법과 예제 코드입니다.}} class=coders100 The Flame Detection Module is a specialized sensor designed to detect the presence of flames or fire within its proximity. This module is highl..."

2024-03-24T02:47:00Z

Created page with "{{#seo:|title=아두위키 : 불꽃 감지 모듈|keywords=아두이노,불꽃감지모듈,아두이노 불꽃감지모듈, 아두이노 센서 예제, 불꽃감지모듈 예제|description=아두이노에서 불꽃감지모듈을 사용하는 방법과 예제 코드입니다.}} center|class=coders100 The Flame Detection Module is a specialized sensor designed to detect the presence of flames or fire within its proximity. This module is highl..."

새 문서

{{#seo:|title=아두위키 : 불꽃 감지 모듈|keywords=아두이노,불꽃감지모듈,아두이노 불꽃감지모듈, 아두이노 센서 예제, 불꽃감지모듈 예제|description=아두이노에서 불꽃감지모듈을 사용하는 방법과 예제 코드입니다.}}
[[File:불꽃 감지.jpg|center|class=coders100]]

The Flame Detection Module is a specialized sensor designed to detect the presence of flames or fire within its proximity. This module is highly sensitive to the wavelengths of light produced by flames, typically in the range of 760nm to 1100nm, allowing it to distinguish fire from other light sources.

== '''Specifications''' ==

* Operating Voltage: 3.3V ~ 5V
* Detection Angle: 60 degrees
* Sensing Distance: Up to 17cm ~ 18cm
* Detection Wavelength: 760nm ~ 1100nm

== '''Connection''' ==
The circuit used in the example code below.

An LED can be replaced with another module or omitted entirely.
{| class="wikitable"
| colspan="2" rowspan="1" |Resistor
| colspan="2" rowspan="1" |Flame Detection Module
| colspan="1" rowspan="1" |LED
| colspan="2" rowspan="1" |Arduino
|-
| colspan="2" rowspan="1" |
| colspan="2" rowspan="1" |VCC
| colspan="1" rowspan="1" |
| colspan="2" rowspan="1" |5V
|-
| colspan="2" rowspan="1" |
| colspan="2" rowspan="1" |GND
| colspan="1" rowspan="1" | -
| colspan="2" rowspan="1" |GND
|-
| colspan="2" rowspan="1" |Connection
| colspan="2" rowspan="1" |
| colspan="1" rowspan="1" | +
| colspan="2" rowspan="1" |
|-
| colspan="2" rowspan="1" |
| colspan="2" rowspan="1" |DO
| colspan="1" rowspan="1" |
| colspan="2" rowspan="1" |D8
|-
| colspan="2" rowspan="1" |Connection
| colspan="2" rowspan="1" |
| colspan="1" rowspan="1" |
| colspan="2" rowspan="1" |D7
|}
[[File:불꽃 감지 모듈 회로.png|center|class=coders100]]

== '''Example Code''' ==
<syntaxhighlight lang="c++" line="1">
// Code to turn on the LED when a flame is detected.
#define led 7
#define fire 8

int state = 0;

void setup() {
pinMode(fire, INPUT);
pinMode(led, OUTPUT);
digitalWrite(led, LOW);
}

void loop() {
state = digitalRead(fire);
if (state == 0) digitalWrite(led, HIGH); // Flame detection outputs 0
else digitalWrite(led, LOW);
}

</syntaxhighlight>

=== Execution Result ===
[[File:불꽃 감지 테스트.png|center|class=coders100]]

Flame Detection Module - 편집 역사